Kenwood Tk 880 Programming Ham Radio Software Just By#
Kenwood Tk 880 Programming Ham Radio Full Quieting Signal#
Kenwood Tk 880 Programming Ham Radio Password Protected TK#

The price may differ greatly compared to locally sourced The main category is Manuals of amateur radio transceivers and equipment. View Offer This is an import. USB Programming Cable For Kenwood Radio RJ45 / 8-Pin, For 32 and 64 bit Windows and Mac operating systems Brand: Goodqbuy Model: B01CJNPY6K from R489.00. GoodQbuy USB Programming Cable For Kenwood Radio TK-863G TK-868 TK-868G TK-880 TK-880G TK-8108 TK-8150 RJ45 8-PIN.

Kenwood Tk 880 Programming Ham Radio Password Protected TK

Kenwood Tk 880 Programming Ham Radio Software Just By

To read a password protected TK-981 perform the following steps:Kenwood TK-880-1 LTR/Conventional UHF 25 Watt radio. This password protection only protects the file from being read from the radio, you can simply overwrite the file in the radio without issue (there is no write password). DAT file programmed in the radio to have a read protection password. While I realize that they are land mobile radios that are programmed with software, I saw a video on youtube where you could set up the frequencies without using software just by using the front panel keys.The Kenwood TK-981 has a feature in the programming software, KPG-49D, that allows the.

The software will now read the radio and you are all set!TK-981 Top/Bottom Cabinet Screw Thread RepairThe Kenwood TK-981 has four M2.6 raised oval countersunk screws that hold the top and bottom cabinets onto the chassis of the radio. When the popup window for the password comes up you will need to press and hold the control (CTRL) keyВ whileВ typing the word 'system' (no quotes), while still holding the CTRL key click 'Ok' or press enter Go to 'PROGRAM' and 'READ DATA FROM RADIO' and read the radio as you would normally. Start KPG-49D (Version 4.xx) and read from the password protected radio Has 32 systems and 250 groups and 250 conventional channels.

If there is a broken off cabinet screw in the chassis of your radio you can drill it out rather easily using a 1/16' drill bit, be sure to use a center punch so that your drill bit doesn't drift and stays on center. This tap size is not common and can usually only be procured via online resources. The tap size you will need is 2.6mm x 0.45mm thread pitch starter tap (finishing/bottoming tap optional).

Kenwood Tk 880 Programming Ham Radio Full Quieting Signal

The firmware has no other special features other then RSSI readout some have referred to this firmware as 'special ham firmware', there's not much special about this firmware other than it has been edited to allow the RSSI feature. These numbers are based off of how strong or weak a signal is into the radio's receiver for example a weak signal would read 45 or thereabouts and a strong full quieting signal would read 130. The modified version 2 RSSI firmware, checksum '7FB8', allows an arbitrary number between ~30 and 140 to be displayed on the upper left side of the display of the radio. This RSSI firmware was based off of Version 2, revision 18, checksum 'E613' firmware. Don't ask them about it!), surfaced allowing RSSI readout on the display of the Version 2 TK-981 and TK-481. If you have a MC-59 DTMF mic and would like to convert the keypad to the KMC-32 DTMF keypad the conversion is quick and painless! Pictured below on the left side of the picture is the amateur radio Kenwood MC-59 DTMF mic, on the right side is the commercial radio Kenwood KMC-32- if you want the keypad of the MC-59 to look like that of the KMC-32 then the KMC-32 Silicone button keypad can be purchased from East Coast Transistor or Pacific CoastTK-981 Received Signal Strength Indication (RSSI) FirmwareSometime in 2010 special amateur radio edited firmware, NOT released by Kenwood (i.e.

To make a cloning cable you will need a small length of 3 conductor cable and two 8-Pin RJ-45 connectors. However, this feature is still handy if you use a beam antenna and rotor so that you can aim the antenna in the direction of the RF signal you are trying to receive, but other than that use, the displayed RSSI number is more of a novelty.Pictured below are the results of bench testing the TK-981 RSSI firmware feature.This chart is downloadable in PDF TK-981 RSSI Example ChartA plot of signal strength, in dBm, into the receiver verses the displayed RSSI value is pictured below.This plot is downloadable in PDF TK-981 dBm vs RSSI DisplayedA plot of signal strength, in dBm, into the receiver verses the voltage at the RSSI test pads on the main RF board is pictured below.This plot is downloadable in PDF TK-981 dBm vs RSSI VdcIf you want to use the clone feature that the TK-981 is capable of its rather easy to make your own cloning cable. One thing that is very important to remember is that every radio will be slightly different in other words there is no universal chart that corresponds RF signal strength, in dBm or uV, to a displayed RSSI readout- therefore if you were to take the charts shown below and compare them to your TK-981 by injecting the same RF signal levels into your radio, the RSSI value displayed would be different from the ones shown here- it's an arbitrary number unless you make your own dBm to displayed RSSI value chart for your radio.

One TK-981 (the MASTER radio) will be used to transfer data to a second TK-981 (the SLAVE radio). Please note that the view shown is looking down, with the pin side facing up, on each RJ-45 connector.To clone a Kenwood TK-981 to another TK-981: The diagram below will aid you in making a clone cable. If you would prefer to purchase a cloning cable rather than build one they are no longer available from East Coast Transistor or Pacific Coast Parts.

The SLAVE radio will display 'PROGRAM' on the display. Press the 'SCN' button on the MASTER radio to start the clone process. Connect the cloning cable between the MASTER and SLAVE radio. On the radio you are going to be CLONING TO (the SLAVE radio) power on the radio as you would normally. On the radio you are going to be CLONING FROM (this is the MASTER radio that has Cloning enabled in step 1 above) power on the radio with the 'C' button held down for 5 seconds, then release, the display will read 'CLONE MODE'- this is the MASTER radio. To enable the Clone feature in the MASTER radio DAT file use KPG-49D and go to the 'Edit' menu and then select 'Optional Features' from there click on the 'Optional Features 2' tab and under the 'Mode' section select the 'Clone' checkbox, write this DAT file back to the MASTER radio.